Our dining room has the perfect empty wall above my edible printer that, in searching Pinterest, I knew I wanted to cover with a gallery of plates. However, there were only a few ideas on how to do so, and none of them seemed that appealing to me. Let me explain...
First off, I was not in any way, shape, or form going to spend a ton of money on this project. All the plates were bought at Goodwill over the course of a year for CHEAP. Like 29 cents cheap for some of them, and no more than $1.50. I would just check over that section every time I went through, and would usually come away with a few good ones. I actually ended up with too many to put on that wall and ended up sending them back to - you guessed it - Goodwill ;P
When I started doing some research, I found 3 main ways to hang them on the wall:
1.) Gluing safety pins to the back with super glue, as seen here. Some people complained that it would ruin your plates, which is a valid concern if your plates are nice. I couldn't care less about that with my Goodwill plates. But I do care about the printer sitting underneath them and I don't trust my gluing skills that much.
2.) These bad boys:
Not so pretty. And they remind me of bugs...I'm weird, I know. Last option:
So I started looking at the design, and well...it can't be that hard to duplicate, can it?? Turns out, not at all.
First up - you need to get some scissors, duct tape (in whatever color you want - I chose white to match the plates) and these little guys:
D rings are commonly used in sewing, and I found them on the notions wall at Hobby Lobby while they were 50% off, so I paid $1.00 for 6. So, right now, our total lands at 16 cents each hanger. Add in the duct tape, which was $4.99 at Hobby Lobby, minus my 40% off coupon, came to a whopping $2.99. Oh, and tax. So for the 11 plates that I ended up hanging, it cost me - wait for it.... 50 cents each. Boom. (mic drop)
Here's how you can do it, too :)
Take a length of duct tape and cut it in half vertically, so it can fit through the D ring. Slide it sticky side down over the flat side of the ring, which will be on the bottom. The "D" should look like it's laying on its back.
|Sorry this is fuzzy, but I hope it can give you some idea of what I mean.|
Figure out where you want the top of your plate to be, and lay the strap down in that direction. Make sure that you place the D ring above the rim of the bottom so that it will lay flat against the wall.
Cut a few more strips of duct tape and tape the strap to the plate. Rub it on really well.
And you're done :D Sturdy, easy, and cheap. Love when things work out that way!!
To hang the plates on the wall, I saw a trick that suggested tracing the plates onto paper and hanging those on the wall. I went one step a bit more than that. First, I laid out all the plates on the ground in the arrangement I wanted. This was really hard for me and took the most amount of time. I couldn't figure out what overall shape I wanted them to be or which plates to put where. But I finally got there!
|In process of figuring out how I wanted to hang them.|
Using painters tape, I taped the newspaper templates on the wall and got them lined up the best I could...stupid light switch was in the way and messed up my order, but it's fine. Just don't look too closely.
Then all I had to do was hammer a nail angled up where I had marked the hangers on the templates...
...pull the paper off and hang the plates on the nails.
I thought it looked a little plain, so I added some vinyl decals from the Silhouette store (and one I designed) to a few of them. The jury's still out on how I feel about them, but I figure I'll leave them around for a little while so I can make up my mind.
Anyway, there you have it. A cheap, simple, easy, and fast way to hang up your own gallery wall. If y'all use this method, I'd love to see how yours turn out!
***UPDATE - after months, these did start loosening because of the weight of the plates. If you are proactive, then you should have no problems and can either stick back on or replace. But please, do not use this method to hang anything valuable. One of my Goodwill plates fell off because it was so heavy. It didn't break, because it fell on the carpet, but just wanted to let y'all know in the spirit of full disclosure :D***